|
System Overview
The Intrusion Alarm System provides for detecting and
alerting the occupants, of any attempted entry through
all entry or exit poits, windows and also provides for
detecting the movement of an intruder within the protected
premises.
IAS provides to deter an intruder or provides an alert
by setting off an siren on detecting intrusion. In addition
to intrusion detection, this device also includes systems
like:
- LPG Gas Leak Detector
- Smoke Detector
- Emergency Panic Button
- Communicator (Auto Dialer)
Components of Intrusion Alarm System
(IAS)
An Intrusion Alarm System (IAS) typically consists
of an Intruder Panel, PIR(Passive Infra Red) Movement
Detectors, Vibration Detectors, Glass Break Detectors,
Magnetic Door Contact, LPG Gas Detector, Smoke Detector,
Hooters, an Panic Button, Communicator, Battery Back
Up and an optional Central Monitoring System (CMS) facility.
- 8 Zones - Each zone is separately identified on
the keypad and provides ample security detection for
most domestic properties.
- 3 Part Set Programs - Allows three programmed setting
levels dependent on the people in the property or
the level of protection required.
- Simple Set Readers for Ease of Operation - Up to
4 stylish readers can be used to set/unset the system
using a proximity keyfob.
- Personal Attack Facility - Any number of PA buttons
may be set to activate the system in an emergency.
- Remote Keypads for added Flexibility - Up to four
keypads can operate the system from any point in the
property.
- Input for Remote Keyswitch or Push to Set Switch
- A remote keyswitch or push can be used to set or
unset the system.
- Fire Zone - Any number of zones can be programmed
as a fire zone. Two types are available: Standard
Fire - operated only whwn system has been set; 24
hour - operates all the time.
- Lighting Control Feature - Full manual and automatic
control over security lightng.
- Duress Code - Allows the user to unset the system
and silence the alarm under duress, using a second
code that will communicate an alarm to an alarm receiving
center.
- Chime - Can be used to select a low secuiryt chime
alarm for various areas of the protected area, even
when the main alarm is turned off.
- Built-in tamper control
PIR Movement Detectors
The salient features of the range of movement detctors
are as follows:
- Look Down Technology - Dual lookdown zones are
employed to ensure that even the most determined intruder
will be detected.
- NC/NO Selectable Outputs - Products are fitted
with changeover relays to ensure compatibility with
all requirements.
- White Light Filter Lens - To minimize any possibility
of problematic alarms due to fluorescent / environmental
conditions.
- Intelligent Pulse Counts - Reduces the possilbility
of false alarms caused by environmental and power
line interference.
- Sealed Optics - The sensor element is sealed, to
prevent unwanted small insects form accessing the
sensor area.
Vibration Detectors
These are solid state detectors with no moving parts
and therefore non-gravity dependent.it offers a flashing
LED indication that can be remotely reset or lewft illuminated
to act as a deterrent. Sensitivity is controlled by
a variable potentiomater coupled with a dual sensitivity
link thus offering fine adjustment possiiblities. In
sites that offer high probability of single unintentional
impacts, a patent double knock feature is provided.
The Salient feature are as follows:
- Removable Electronics
- Non gravity dependent
- Dual memory LED and relay
- Walk test facility
- Remote rest
- Dual stage sensitivity
- Sensitivity potentiometer
- LED lens relay auto resets
- Surface mount technology
- Anti condensation base
- Door contact option
- Double knock link
Glass Break Detectors
Glass Break Detctors rely on the sound and aftershock
of a breaking glass to trigger an alarm. These glass
break detectors monitor windows and glass doors.
The detectors register the shock frequency of the breaking
glass. Surface-mounted glass-break detectors are mounted
on the glass itself. The detector is programmed to both
register the shock and hear the specific frequencies
of the breaking glass before raising an alarm.
Magnetic Door Contact
Magnetic Door Contact detectors identify intruders by
using a magnet and reed switch mechanism. The reed switches
are electrical contacts held open by the presence of
a magnet. When a magnet attached to an opening door
moves away from the reed switches in the alarmed sensor,
the switches make contact with each other and trigger
a radio frequency (RF) transmission to the system control
panel. Information in the RF transmission identifies
the type and location of the sensor.
Magnetic Door Contact Detctors can be surface-mounted
or recessed. Absence of any external wiring provides
the installer with unlimited scope to place the device
in positions where it is hidden from view. The detector
is a truly stand alone module containing the low power
viper integrated circuit, identification and encoding
electronics, scantronic transmitter, integral aerial
and battery.
Salient features include:
- Simple calibration
- Exclusive double knock facility at point of attack
- Wire free
- Scantronic 4600 series compatible
- Adjustable detection sensitivity
- Fully approved transmitter
- Integral magnetic door contact
LPG Gas Detector
LP gas (butane or propane) is the most common type of
fuel used for cooking and heating worldwide. LPG leak
can cause devastating explosions and consequences of
a gas leak in both domestic and commercial situations
are every bit as disastrous as those of a fire and can
be avoided with the fitting of easy to use and cost
effective detection equipment.
Feature and Benefits are as follows:
- Officially approved to BS7348 (The British Standards
for Domestic Gas Detectors).
- Proven semiconductor sensor technology.
- 230Vac or 12Vds versions.
- Relay output models are available.
- Suitable for home, caravan and commercial use.
- Easy to install and use with no maintenance.
Smoke Detector
Smoke Detectors provide the earliest practicable fire
detection and warning. This system consists of smoke
or heat detectors at designated locations, to detect
smoke or heat at the earliest during any outbreak of
fire. The various types of detectors used in this system
are Photoelectric, Heat and Multisensing. The detectors
are selected based on certain pre-determined parameters.
On sensing fire the system initiates a warning alarm,
thereby alerting the occupants.
Hooter
The hooters offered are sophisticated, stylish and highly
featured solution to external sounder requirements.
The features are:
- Easily mountable
- Rugged strobe with panaromic lens
- Sound output - 108 db - 113 db
- Selectable timer
- Dual ring mode
- Alternating comfort Leds
- Selectable sounder cut-off timer
Panic Button
Panic buttons are targeted and rapid mode of contact
used primarily by sick and old people to contact their
care takers at times of distress or during emergency
situations. It offers either visual or acoustic signaling.
The signals can also be routed to the wireless devices
carried by their caregivers, enabling a fast and quick
response. This system typically consists of a main communicator
panel and the multiple points connected to it.
Auto Dialer
The communicator / auto dialer is pre programmed to
place 4 automatic calls to any pre set destinations,
which could include the owner, other two important numbers
and one to the Central Monitoring System (CMS).
The salient features are:
- Up to four keypads per control panel
- Full LCD status indication
- Illuminated keys
- On-board PA facility Entry / exit tones
- Programmable user strings
- Programmable backlight options for keypad and LCD
display
Central Monitoring System (CMS)
This is an optional facility available by paying an
annual subscription fees. The IAS device can be connected
to a CMS that provides:
- A round the clock online monitoring facility
- Auto back-up and emergency reminder
- Deputes trained personnel towards distress target.
This comprehensive Intrusion Detection and Alarm system
is available as a box and is highly customizable to
suit individual corporate, retail or residential security
needs. The customer also has an option of choosing from
either a regular wired Intrusion Alarm System(IAS) or
a wireless Intrusion Alarm System(IAS). A Wireless IAS,
in addition to the above components also consists of
a Remote and LED.
Target Segment
- Corporate Offices
- Retail Outlets
- Apartments
- Residences
Alliances
Novar Plc.
|
